Full metadata record
DC FieldValueLanguage
dc.contributorDepartment of Applied Biology and Chemical Technologyen_US
dc.contributor.advisorLo, Chun Lap (ABCT)-
dc.contributor.advisorLo, Wai Hung (ABCT)-
dc.creatorChan, Kwan Shing-
dc.identifier.urihttps://theses.lib.polyu.edu.hk/handle/200/10595-
dc.languageEnglishen_US
dc.publisherHong Kong Polytechnic Universityen_US
dc.rightsAll rights reserveden_US
dc.titleEffective adsorptive removal of heavy metal ions by aggregated MoS₂ nanoflakes with edge site exposureen_US
dcterms.abstractRecently, metal-sulfide-based adsorbents have garnered a lot of attention with regard to heavy metal recovery due to their intrinsic selectivity to soft metal ions. Molybdenum sulfide (MoS₂), a novel two-dimensional material, was identified as a suitable metal sulfide adsorbent with good acid and air stability. In this study, different MoS₂ materials were prepared by a facile hydrothermal method with different optimization approaches: the doping of metal, adjustment of precursor concentration and incorporation of mesocellular siliceous foams (MCF). The MoS₂ formation was confirmed by Raman spectroscopy and elemental analysis. Metal screening studies revealed that the MoS₂ materials could effectively immobilize Cu²⁺, Hg²⁺, Ag⁺ and Pb²⁺ Cu²⁺ was chosen for further investigation because Cu²⁺ received less interference from potential side reactions and the formation of metal molybdate. All the MoS₂ materials were investigated for Cu²⁺ adsorption performance. Based on the screening data on Cu²⁺ adsorption, MoS₂-1:4 and MoS₂-1:7 were selected for further adsorption studies, including kinetics, isotherm, effect on pH, effect on salt and regeneration and reuse of the material. A kinetic study reveals that the Cu²⁺ adsorption on MoS₂-1:4 and MoS₂-1:7 was completed in a 180-240 minute contact time frame with ~99% removal. The Elovich model is the best model to describe the Cu²⁺ adsorption kinetics of MoS₂-1:4 and MoS₂ The isotherm study demonstrates that the maximum Cu²⁺ adsorption capacities of MoS₂-1:7 and MoS₂-1:4 calculated from Sips isotherm are 201.35 and 226.20 mg/g respectively. Isotherm modelling reveals that both non-linear Dubinin-Radushkevitch and Sips isotherms can best simulate the equilibrium data of Cu²⁺ adsorption on MoS₂-1:4, while the Sips isotherm is the best model for simulating the data of Cu²⁺ adsorption on MoS₂-1:7. In addition, the optimal pH range for the Cu²⁺ adsorption on MoS₂-1:4 and MoS₂-1:7 was between 4 and 6. The zeta potential study suggests that coulombic interaction between the positively-charged Cu²⁺ and the negatively-charged MoS₂ is one of the driving forces for the Cu²⁺ adsorption. In the desorption study, 86% of the adsorption capacity of MoS₂-1:7 remained after three adsorption/desorption cycles using 1.0 M HCl as a desorbing agent. A combination of scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), X-ray photoelectron spectroscopy (XPS), X-ray diffractometry (XRD), N₂-adsorption/desorption isotherm measurement and zeta potential measurement, was used to evaluate and characterize the Cu²⁺ adsorption mechanism. The SEM images reveal that MoS₂-1:4 and MoS₂-1:7 are wire-brush like and are composed of aggregated MoS₂ nanoflakes with edge site exposure. The formation of nanosheets in MoS₂-1:4 and MoS2-1:7 are also confirmed by the XRD analysis of the MoS₂ materials. The XPS studies have discovered that the S₂²⁻ species located at the edge sites of MoS₂ nanosheets contributes significantly to the binding of Cu²⁺. This study shows that aggregated MoS₂ nanoflakes with edge site exposure have been successfully synthesized by a facile hydrothermal method. The MoS₂ nanoflakes have demonstrated great potential as a highly effective adsorbent for the removal of Cu²⁺ from wastewater and contaminated water. The role of S₂²⁻ species in the adsorption of Cu²⁺ on the MoS₂ nanosheets was first reported in this study. This can offer an alternative strategy to the precise engineering of MoS₂ adsorbent in the future.en_US
dcterms.extentxii, 143 pages : color illustrationsen_US
dcterms.isPartOfPolyU Electronic Thesesen_US
dcterms.issued2020en_US
dcterms.educationalLevelM.Phil.en_US
dcterms.educationalLevelAll Masteren_US
dcterms.LCSHMolybdenum compoundsen_US
dcterms.LCSHMetal ions -- Absorption and adsorptionen_US
dcterms.LCSHHeavy metals -- Absorption and adsorptionSorbentsen_US
dcterms.LCSHHong Kong Polytechnic University -- Dissertationsen_US
dcterms.accessRightsopen accessen_US

Files in This Item:
File Description SizeFormat 
5025.pdfFor All Users4.46 MBAdobe PDFView/Open


Copyright Undertaking

As a bona fide Library user, I declare that:

  1. I will abide by the rules and legal ordinances governing copyright regarding the use of the Database.
  2. I will use the Database for the purpose of my research or private study only and not for circulation or further reproduction or any other purpose.
  3. I agree to indemnify and hold the University harmless from and against any loss, damage, cost, liability or expenses arising from copyright infringement or unauthorized usage.

By downloading any item(s) listed above, you acknowledge that you have read and understood the copyright undertaking as stated above, and agree to be bound by all of its terms.

Show simple item record

Please use this identifier to cite or link to this item: https://theses.lib.polyu.edu.hk/handle/200/10595