Full metadata record
DC FieldValueLanguage
dc.contributorDepartment of Industrial and Systems Engineeringen_US
dc.creatorKwok, Tsz-chun-
dc.publisherHong Kong Polytechnic University-
dc.rightsAll rights reserveden_US
dc.titleAn investigation of factors affecting surface generation in ultra-precision machining with fast tool servoen_US
dcterms.abstractUltra-precision machining with fast tool servo (FTS) is one of the emerging technologies for the fabrication of high-quality optical surfaces. A diamond tool is fixed on the FTS is activated back and forth by a stacked type of piezoelectric actuator. Complex optical surfaces with sub-micrometer form accuracy and nanometric surface finish can be fabricated without the need for any subsequent post processing. Although there has been extensive research work on the design and control of tool actuators for FTS machining, relatively little research work has been reported in the study of nano-surface generation in FTS machining. As a result, this study aims at investigating the factors affecting surface generation in ultra-precision machining with FTS. The factors under investigation include process factors, wear of diamond tool and error motion of FTS actuation. Regarding process factors, a series of experiments were conducted under various cutting conditions such as spindle speed, feed rate, depth of cut, etc. The results indicate that the surface quality of the machined surface can be improved by appropriate selection of cutting conditions. Moreover, a tool compensation method has been developed which is found to be effective in improving the surface quality of machined surfaces. To study the form errors in FTS machining of optical components with complex profiles such as micro-lens arrays, pattern analysis has been employed to determine the surface quality of the machined surface. The experimental results indicate that the influence due to process factors can be minimized with appropriate selection of cutting conditions.en_US
dcterms.abstractSince a diamond tool with a small radius is usually used in FTS machining, the surface quality of the workpiece is highly susceptible to the tool wear. As a result, the study continues by investigating the effect of the tool wear in FTS machining. A series of cutting experiments were conducted by FTS machining of a tilted flat surface by a predetermined distance. The traditional method for determination of tool wear based on the maximum height and the width of flank wear has been used to characterize the tool wear. In order to investigate the diamond tool wear quantitatively, a digital image processing method has been proposed to quantitatively characterize the tool wear. It is not only found to be effective in exploring the wear phenomena but also quantifying the material loss in various wear stages of the diamond tool. To investigate the effect of tool wear on surface generation in FTS machining, an experimental study has been done by machining tilted flat surface and micro-lense array. It is interesting to note that the form error of the FTS machined surface is adversely affected by tool wear. As FTS machining technology is built based on the single-point diamond turning technology, the error motion of the ultra-precision machine and the stroke error of the FTS play important roles in the surface generation. Based on the experimental results and cutting mechanisms in FTS machining, a theoretical analysis is attempted to address two major error motions, which are due to the systematic characteristics of the ultra-precision machine and the stroke error due to the FTS actuation. Afterwards, a surface generation model was established to predict the surface quality in terms of the form error in FTS machining. The model has been verified through a series of cutting experiments. The result shows that the trend of the theoretical prediction by the simulation system is found to agree reasonably well with the experimental results. On the whole, this study not only contributes significantly to a better understanding of the factors affecting surface generation in FTS machining but also provides an important means for the improvement of the surface quality in ultra-precision machining with Fast Tool Servo. This is vital for the technological achievement of ultra-precision machining technology.en_US
dcterms.extentxix, 207, [15] leaves : ill. ; 30 cm.en_US
dcterms.isPartOfPolyU Electronic Thesesen_US
dcterms.educationalLevelAll Masteren_US
dcterms.LCSHDiamond turning.en_US
dcterms.LCSHMachine-tools -- Monitoring.en_US
dcterms.LCSHSurfaces (Technology)en_US
dcterms.LCSHHong Kong Polytechnic University -- Dissertationsen_US
dcterms.accessRightsopen accessen_US

Files in This Item:
File Description SizeFormat 
b24561769.pdfFor All Users12.1 MBAdobe PDFView/Open

Copyright Undertaking

As a bona fide Library user, I declare that:

  1. I will abide by the rules and legal ordinances governing copyright regarding the use of the Database.
  2. I will use the Database for the purpose of my research or private study only and not for circulation or further reproduction or any other purpose.
  3. I agree to indemnify and hold the University harmless from and against any loss, damage, cost, liability or expenses arising from copyright infringement or unauthorized usage.

By downloading any item(s) listed above, you acknowledge that you have read and understood the copyright undertaking as stated above, and agree to be bound by all of its terms.

Show simple item record

Please use this identifier to cite or link to this item: https://theses.lib.polyu.edu.hk/handle/200/6152