Full metadata record
DC FieldValueLanguage
dc.contributorDepartment of Electrical Engineeringen_US
dc.creatorZhang, Zhu-
dc.identifier.urihttps://theses.lib.polyu.edu.hk/handle/200/6813-
dc.languageEnglishen_US
dc.publisherHong Kong Polytechnic University-
dc.rightsAll rights reserveden_US
dc.titleApplication of linear switched reluctance actuator in active suspension systemsen_US
dcterms.abstractElectromagnetic active suspension system is attracting more and more attention due to recent advances in motor design, power electronics and modern control method. Compared to the hydraulic active suspension system, it is more energy-efficient, and has a faster dynamic response. In this thesis, a novel configuration of linear switched reluctance actuator (LSRA) is proposed for the application in active suspension system. The robust construction, low manufacturing and maintenance cost, less thermal problem, good fault tolerance capability and high reliability in harsh environments make LSRA attractive alternative to permanent magnet actuator. In order to determine the requirements on actuator design, the effects of suspension parameters on system characteristics are analyzed by the frequency response Bode plots method. A Linear Quadratic Regulator (LQR) controller is developed and simulated with the quarter-vehicle model to obtain the optimal force requirement on LSRA. By considering the requirements and constraints, a novel configuration of LSRA that comprises of four double-sided modules is proposed. The whole design procedure, ranging from the determination of basic actuator parameters to the calculation of flux linkage and force characteristics, is demonstrated in this thesis. The accuracy of the analytical design is then verified by the finite element method (FEM). Besides, the longitudinal and transversal end effects of double-sided LSRA are evaluated by analyzing the sensitivities of translator position and excitation current.en_US
dcterms.abstractTo improve the performance of designed actuator, a multi-objective optimization method to obtain higher average force, reduced force ripple and higher force density is proposed in this thesis. Some practical constraints are taken into consideration in the optimization procedure. The effects of stator and translator pole width on the three optimization criteria and the actuator volume are analyzed. Based on the optimized specification, a prototype of the proposed LSRA was fabricated. The flux linkage and force characteristics were measured to verify the theoretical design. Finally, an improved direct instantaneous force control (DIFC) scheme for four-quadrant operation of the proposed LSRA is developed. The controller incorporates adaptive force distribution function (FDF), instantaneous force estimation, hysteresis force controller and on-line determination of switching positions. By introducing the on-line estimated force of outgoing phase to FDF, the force demand of incoming phase is adaptively adjusted. Hence, the force ripple can be minimized over a wider range of switching positions. On the other hand, the operational efficiency is improved by on-line optimizing the switching positions according to the force demand. The simulation and experimental results demonstrate the effectiveness of the proposed control scheme.en_US
dcterms.extentxx, 151 leaves : ill. (some col.) ; 30 cm.en_US
dcterms.isPartOfPolyU Electronic Thesesen_US
dcterms.issued2012en_US
dcterms.educationalLevelAll Doctorateen_US
dcterms.educationalLevelPh.D.en_US
dcterms.LCSHActuators -- Design and construction.en_US
dcterms.LCSHMotor vehicles -- Springs and suspension.en_US
dcterms.LCSHHong Kong Polytechnic University -- Dissertationsen_US
dcterms.accessRightsopen accessen_US

Files in This Item:
File Description SizeFormat 
b25513035.pdfFor All Users3.73 MBAdobe PDFView/Open


Copyright Undertaking

As a bona fide Library user, I declare that:

  1. I will abide by the rules and legal ordinances governing copyright regarding the use of the Database.
  2. I will use the Database for the purpose of my research or private study only and not for circulation or further reproduction or any other purpose.
  3. I agree to indemnify and hold the University harmless from and against any loss, damage, cost, liability or expenses arising from copyright infringement or unauthorized usage.

By downloading any item(s) listed above, you acknowledge that you have read and understood the copyright undertaking as stated above, and agree to be bound by all of its terms.

Show simple item record

Please use this identifier to cite or link to this item: https://theses.lib.polyu.edu.hk/handle/200/6813